Amada HFA400W Band Saw

FEATURES+

Blade Deviation Monitor
Auto Trim Cut
Blade Deviation Monitor
Chip Conveyor
Full Stroke Vises
Motion Detector
NC Back Gauge
Pressure Flow Valve
Self Diagnostics
Variable Blade Speed Drive
Wheel Cover Limit Switch

SPECS+

Cutting Capacity – Round (diameter)	0.5″ – 16″ (13 – 420 mm)
Cutting Capcity – Rectangle (W x H)	16″ x 16″ (400 x 400 mm)
Work Load Capacity	5,511 lbs (2,500 kg)
Blade Dimensions	15′ x 0.050″ x 1-1/2″ (4570 x 1.3 x 41 mm)
Blade Speed	50-295 ft./min, 60Hz Stepless (15-90 m/min, 50/60Hz Stepless)
Tension Control	Hydraulic
Vise Operation Type	Front and Rear Vise
Blade Saw Motor	8 HP (5.5 kW)
Hydraulic Pump Motor	2 HP (1.5 kW)
Cutting Fluid Pump Motor	1/4 HP (0.18 kW)
Power Supply Voltage	AC220±10%, 3 PH, 60 Hz (Or AC440V, 3PH, 60Hz)
Power Requirement	12.8 kVA
Cutting Fluid Tank Capcity	31.5 gal (120 Liters)
Cutting Fluid Pump Type	Electric
Hydraulic Tank Capcity	10.5 gal (40 Liters)
Chip Disposal	Chip Conveyor
Material Index Mechanism	Shuttle Vise
Stroke	19.6″ (500 mm)
Machine Dimensions – Head Up Position	95.5″ x 106.3″ x 95.5″ (2426 x 2701 x 2425 mm)
Machine Dimensions – Head Down Position	90.0″ x 106.3″ x 62.4″ (2285 x 2701 x 1585 mm)
Table Height (Above Floor)	31.5″ (800 mm)
Machine Weight	4,851 lbs (2,200 kg)

MEDIA+

Please call for more information about Amada band Saw Model HFA400W 1 (800) 286-3624

OPTIONS+

	AXCELA G SERIES Band Saw Blades High-performance Carbide Tipped Band Saw Blades High-quality carbide tips and the dove tail tooth shape. AXCELA makes incredible cutting speed for hard to cut material.
	BCTBR Band Saw Blade Multi Faceted Carbide Tipped Blade Designed exclusively for heat-resistant alloys, nickel-based alloys, titanium alloys, and special cast tensile steels, all with high tensile strength of over 142,000 psi. It features ultra-hard, diamond sharp carbide tipped teeth that resist low thermal conductivity and abrasion that can quickly break down conventional bi-metal type bands.
	MAGNUM HI-LO Band Saw Blade Patented Varying Tooth Height and Set M-71 Bi-metal Blade High-quality carbide tips and the dove tail tooth shape. AXCELA makes incredible cutting speed for hard to cut material.
	Hi-Lo Band Saw Blade Varying Tooth Height Design, M-42 Welded Edge The Hi-Lo blade features a high and low teeth height design and a 15-degree rake angle. The blade is ideal for cutting hard steels.
	CHIP BREAKER Band Saw Blade Patented Gullet Design Designed to reduced heat generated at increased chip load. With reduced tooth stripping and breaking this equates to the lowest possible cost per square inch of metal cutting.
	SGLB Band Saw Blade M-42 Bi-metal Blade The SGLB was designed to cover a broad range of cutting applications and to provide maximum efficiency in sawing wear-resistant tool steels. The blade’s tough M-42 cobalt edge resists heat and abrasion, while the varied pitch tooth form expands the ranges of sizes and shapes that can be sawed successfully without changing blades.
	COBALT8 Band Saw Blade Amada Modified M42 High-Speed Steel Bi-Metal Blade General-purpose blade ideal for cutting mild steel and structural steel. “Chip Curler” tooth shape and unique set pattern result in longer blade life.
	SMARTCUT BAND Band Saw Blade Thinner Blade of SGLB and Magnum Hi-Lo Thinner more than 10% from regular SGLB or Magnum Hi-Lo. Specialized Blade for PCSAW330
	PROTECTOR EX M42 Band Saw Blade Exclusive use for structural steel with M-42 Edge. Which has both strength against tooth chipping and high wear resistance. PROTECTOR EX added to the back face of the tooth tip prevents excessive cutting.
	PROTECTOR Band Saw Blade Exclusive Use for Structual Steel with M-30 Matrix Bi-metal Blade Exclusive use for structural steel. Protector provides long blade life and prevents tooth breakage, eliminating excessive tooth stripping. It can withstand the shock of interrupted cuts, allowing for heavier penetration for faster cutting rates. Protector uses a broaching style set pattern designed to eliminate pinching, which prevents the blade from binding the cut.
	MGLB Band Saw Blade General Purpose Matrix Bi-metal Blade The MGLB is best suited for cutting structural shapes, tubing and stacks of mild steel pieces. The MGLB allows band saw machines to cut a wide range of material sizes and shapes without requiring a change of blades. Its tough high-speed steel teeth resist chipping, stripping and abrasion. It can also tolerate the occasional improper speeds and feeds that are often used by inexperienced saw operators.

Description

The Amada HFA400W Band Saw is a horizontal NC Controlled Full Automatic Metal Cutting Band Saw.

Fully automatic band saws with very accurate material indexing controlled by NC-positioning.

Cutting Capacity, Round (Diameter): 0.5″ – 16″

7.5 HP
1-1/2″ Blade
NC Back Gauge
Motion Detector
Self Diagnostics
Variable Blade Speed
Full Stroke Vise

Saw Head Frame

The rigid ‘C’ section frame carries the mountings for the two band wheels, heavy-duty worm drive gear reducer, the band drive motor, and saw guide arm mounting supports.

Band Wheels & Drive System

The band wheels are cast iron for long, productive life. The deflection free 9.4 inch (240 mm.) wheel spindles ensure the wheels run true regardless of tension stress or cutting loads. The spindle assemblies incorporate tapered roller bearings for greater rigidity and long service life. The wheel tracks the blade so that the back of the band contacts the wheel flanges to support the band. The drive motor is coupled to the transmission through a variable speed pulley.

Drive Wheel Transmission

The drive wheel transmission is designed and built by Amada to provide high-efficiency speed reduction, which requires no external cooling, to deliver more power to the large diameter drive hub. This hub ensures that this developed torque is transferred to the blade with no strobing, enabling the machine to efficiently cut high alloys as well as free machining materials.

Idler Wheel Motion Detector

The wheel motion detector will turn off the blade drive in the case where a blade breaks or is jammed in the workpiece. This feature also prevents premature wear on the drive wheel from a stalled band.

Automatic, Powered Chip Conveyor

The electrically powered chip conveyor auger automatically removes the saw chips from the saw while draining the cutting fluid back into the fluid reservoir. The automatic chip conveyor greatly reduces cleanup time and enables the machine to run longer without operator cleanup.

Full Stroke Vise Clamping

The work holding and index vise cylinders are both full stroke which eliminates the manual setting of the clamping jaw for the working width.

Narrow Profile Front Vise

The narrow front vise assembly reduces the butt end remnant to a minimum of 0.3 in. (8 mm.)

Call the Ocean Machinery sales team TODAY at (954) 956-3131 or Toll Free 1 (800) 286-3624 or fill out our online info request form for more information on the Amada HFA400W Band Saw.

Amada HFA400W
Band Saw