Amada VM2500 Band Saw

FEATURES+

Blade Deviation Monitor
Chip Conveyor
Cutting Length Control
Hydraulic Blade Guides
Motion Detector
Remote Blade Guide Setting
Variable Blade Speed Drive
Wheel Cover Limit Switch

SPECS+

Cutting Capacity (L x H)	98.4″ x 20″ (2500 x 500 mm)
Throat Depth	20″ (500 mm)
Work Load Capacity	11,023 lbs (5,000 kg)
Blade Dimensions	15’4″ x 0.050″ x 1-1/2″ (4670 x 1.3 x 41 mm)
Blade Speed	60-295 ft./min, 60Hz Stepless (17-90 m/min, 60Hz Stepless)
Tension Control	Hydraulic
Blade Cutting Control	Hydraulic Pressure – Flow Control Valve
Blade Saw Motor	8 HP (5.5 kW)
Hydraulic Pump Motor	2 HP (1.5 kW)
Cutting Fluid Pump Motor	1/2 HP (0.25 kW)
Power Supply Voltage	AC220±10%, 3 PH, 60 Hz (Or AC440V, 3PH, 60Hz)
Power Requirement	10.7 kVA
Cutting Fluid Tank Capcity	31.7 gal (120 Liters)
Cutting Fluid Pump Type	Electric
Hydraulic Tank Capcity	10 gal (38 Liters)
Chip Disposal	Chip Conveyor
Feed Mechanism	Table Feed, Hydraulic
Feed Stroke	100.4″ (2,550 mm)
Machine Dimensions	73.6″ x 230″ x 106″ (1870 x 5845 x 2700 mm)
Table Height (Above Floor)	39.46″ (1000 mm)
Machine Weight	15,432 lbs (7,000 kg)

MEDIA+

Please call for more information about Amada band Saw Model VM2500 1 (800) 286-3624

OPTIONS+

	AXCELA G SERIES Band Saw Blades High-performance Carbide Tipped Band Saw Blades High-quality carbide tips and the dove tail tooth shape. AXCELA makes incredible cutting speed for hard to cut material.
	BCTBR Band Saw Blade Multi Faceted Carbide Tipped Blade Designed exclusively for heat-resistant alloys, nickel-based alloys, titanium alloys, and special cast tensile steels, all with high tensile strength of over 142,000 psi. It features ultra-hard, diamond sharp carbide tipped teeth that resist low thermal conductivity and abrasion that can quickly break down conventional bi-metal type bands.
	MAGNUM HI-LO Band Saw Blade Patented Varying Tooth Height and Set M-71 Bi-metal Blade High-quality carbide tips and the dove tail tooth shape. AXCELA makes incredible cutting speed for hard to cut material.
	Hi-Lo Band Saw Blade Varying Tooth Height Design, M-42 Welded Edge The Hi-Lo blade features a high and low teeth height design and a 15-degree rake angle. The blade is ideal for cutting hard steels.
	CHIP BREAKER Band Saw Blade Patented Gullet Design Designed to reduced heat generated at increased chip load. With reduced tooth stripping and breaking this equates to the lowest possible cost per square inch of metal cutting.
	SGLB Band Saw Blade M-42 Bi-metal Blade The SGLB was designed to cover a broad range of cutting applications and to provide maximum efficiency in sawing wear-resistant tool steels. The blade’s tough M-42 cobalt edge resists heat and abrasion, while the varied pitch tooth form expands the ranges of sizes and shapes that can be sawed successfully without changing blades.
	COBALT8 Band Saw Blade Amada Modified M42 High-Speed Steel Bi-Metal Blade General-purpose blade ideal for cutting mild steel and structural steel. “Chip Curler” tooth shape and unique set pattern result in longer blade life.
	SMARTCUT BAND Band Saw Blade Thinner Blade of SGLB and Magnum Hi-Lo Thinner more than 10% from regular SGLB or Magnum Hi-Lo. Specialized Blade for PCSAW330
	PROTECTOR EX M42 Band Saw Blade Exclusive use for structural steel with M-42 Edge. Which has both strength against tooth chipping and high wear resistance. PROTECTOR EX added to the back face of the tooth tip prevents excessive cutting.
	PROTECTOR Band Saw Blade Exclusive Use for Structual Steel with M-30 Matrix Bi-metal Blade Exclusive use for structural steel. Protector provides long blade life and prevents tooth breakage, eliminating excessive tooth stripping. It can withstand the shock of interrupted cuts, allowing for heavier penetration for faster cutting rates. Protector uses a broaching style set pattern designed to eliminate pinching, which prevents the blade from binding the cut.
	MGLB Band Saw Blade General Purpose Matrix Bi-metal Blade The MGLB is best suited for cutting structural shapes, tubing and stacks of mild steel pieces. The MGLB allows band saw machines to cut a wide range of material sizes and shapes without requiring a change of blades. Its tough high-speed steel teeth resist chipping, stripping and abrasion. It can also tolerate the occasional improper speeds and feeds that are often used by inexperienced saw operators.

Description

The Amada VM2500 Band Saw is a Vertical Band Saw for precise cutting of blocks and plates in all material grades.

7.5 H.P.
2″ Blade
Chip Conveyor
Cutting Length Control
Hydraulic Blade Guides
Remote Blade Guide Setting

Selective Cutting Height

A cutting height setting can be selected from either 20″ (standard).

Selective Blade Size

A blade can be selected from either a standard 2″ x 0.063″ blade.

Use of Servo Motor and Linear Guide

An AC servo motor and a LM guide are used to move the table for the purpose of accurate cutting control.

Automatic Adjustment of Guide Position

Once a material size is preset, automatic adjustment can be made to determine an optimum guide position. Upon completion of cutting, automatic stop will take place.

Automatically Adjustable Wire Brush

Wire brush contact is automatically adjusted in proportion to wear of wire brush. A message will be displayed to prompt a user to replace the wire brush, when excessive wear is detected.

Excellent Operability

The color display and touch panel facilitate operation. The embedded CNC-Lite function automatically sets optimum cutting conditions.

Back Gauge (optional)

Using an optional back gauge can facilitate the alignment of marks.

Permissible Loading Mass

In response to a trend toward larger materials, the machine table offers 11,025lbs loading mass (4,410lbs for VM-1200).

Call the Ocean Machinery sales team TODAY at (954) 956-3131 or Toll Free 1 (800) 286-3624 or fill out our online info request form for more information on the Amada VM2500 Band Saw.

Amada VM2500
Band Saw